Upgrade Kits and Accessories

Unicover

Unicover
Soundscape Price:$109.00

This is a stylish universal dust cover that protects the platter tonearm and cartridge. Designed for the Gyro SE and Orbe SE models, but fits most other coverless decks as well.

Acrylic Platter/Springs/Adjusters/Inverted Main Bearing Kit

Acrylic Platter/Springs/Adjusters/Inverted Main Bearing Kit
Soundscape Price:$649.00

For early GyroDecs equipped with the aluminum platter and rubber mat.

Inverted Oil-Pumping Main Bearing only

Inverted Oil-Pumping Main Bearing only
Soundscape Price:$299.00

NOTE: When ordering the Upgrade Bearing only, we need the following information in order to supply the correct spindle length on the inverted bearing.

1. Will you be using the bearing with an old style aluminum platter or an acrylic platter?
2. If using with an existing acrylic platter, was this a factory-installed acrylic platter or an upgrade kit platter, installed after purchase of the turntable?

Synthetic Main Bearing Oil

Synthetic Main Bearing Oil
Soundscape Price:$15.00

For use in all turntable bearings. 8cc (1/4 oz.) vial.

Orbe Platter/Clamp Upgrade Kit for GyroDec & Gyro SE

Orbe Platter/Clamp Upgrade Kit for GyroDec & Gyro SE
Soundscape Price:$849.00

Converts acrylic platter GyroDecs or Gyro SE to the Orbe Platter and screw-down clamp. (MKI GyroDecs require a spring change as well. — Call for details.)

2-Piece Decoupled Suspension Tower Upgrade for GyroDec & Orbe

2-Piece Decoupled Suspension Tower Upgrade for GyroDec & Orbe
Soundscape Price:$189.00

For MKI, MKII and MKIII GyroDecs and earlier Orbe. Specify GyroDec or Orbe. Set of 3.

40VA Toroidal AC Power Supply for GyroDec

40VA Toroidal AC Power Supply for GyroDec
Soundscape Price: $199.00

As supplied on the GyroDec MKIV and SE. Replacement for earlier 7VA and 10VA units. Not for later DC-powered decks.

QC MK II Power Supply for AC-powered GyroDec and Gyro SE

QC MK II Power Supply for AC-powered GyroDec and Gyro SE
Soundscape Price:$750.00

Converts acrylic platter GyroDecs or Gyro SE to the Orbe Platter and screw-down clamp. (MKI GyroDecs require a spring change as well.)

DC Power Supply for DC-powered GyroDec and Gyro SE

VC Power Supply for DC-powered GyroDec and Gyro SE
Soundscape Price:$995.00

The VC is a higher current power supply for DC-powered Gyros. It provides for improved music reproduction and speed stability.

DensoDamp Chassis Damping Compound for GyroDec & Gyro SE

DensoDamp Chassis Damping Compound for GyroDec & Gyro SE
Soundscape Price:$35.00

As supplied with the Orbe and Orbe SE.

GyroDec MKIV and SE Stand-Alone Motor Housing Kit

GyroDec MKIV and SE Stand-Alone Motor Housing Kit
Soundscape Price:Silver $279.00
Soundscape Price: Gold $299.00

Prewired stand-alone motor housing will accept your old Gyro motor and top plate, or the new DC motor Upgrade Kit. ($675.00 including DC PSU.) New XLR power connector included for older AC power supplies. Machining of hole in base board and soldering required. (unless converting to SE)

Gyro SE Spider Kit

Gyro SE Spider Kit
Soundscape Price:$119.00

When used with the Stand-Alone Motor Housing Kit, will convert a GyroDec to a Gyro SE.

Orbe SE Spider Kit

Orbe SE Spider Kit
Soundscape Price:$275.00

Will convert an Orbe to an Orbe SE.

33/45/78 RPM 50Hz Pulley

33/45/78 RPM 50Hz Pulley
Soundscape Price:$69.00

For use on Orbe or QC-equipped GyroDec and Gyro SE. (Not for DC powered decks.)

Rega RB300/600 VTA Adjuster Base

Rega RB300/600 VTA Adjuster Base
Soundscape Price:$45.00

Finally, a clever, inexpensive, solution to a perplexing problem! No more arm removals to insert shims. Simply install the Michell VTA Adjustment Base on your Rega RB300 or RB600 tone arm, and you can adjust the vertical tracking angle in minute increments without losing the rigid mounting so important to proper sound reproduction. Requires a 1 1/8" diameter mounting hole. The VTA adjustor, at its' minimum setting, raises the tone arm by 1.75mm, which is slightly less than the thinnest shim (2mm) that REGA manufactures.

Instructions: Loosen the tone arm hold-down nut. Rotate the VTA Adjustment Base to raise or lower the tone arm.
Retighten the hold down nut. So simple!

Record Clamp

Record Clamp
Soundscape Price:$59.00

Black Delrin with silver aluminum knob.

Phono Cartridge Mounting Kit

Phono Cartridge Mounting Kit
Soundscape Price:$15.00

2 each 10mm and 16mm long stainless steel Allen bolts, nuts, washers and Allen key to mount phono cartridges rigidly.